3D Printing Ranked

TPU, Carbon Fiber Nylon and Wood PLA: AMS Slot or External Spool?

Whether a spool can go in your AMS depends on the exact filament, down to the product name, and on which AMS unit you have. This page sets out what Bambu Lab's own pages say for TPU, carbon fiber nylon, wood PLA and the other filaments its AMS guides flag, including where those pages disagree, so you can choose between an AMS slot and the external spool.

The short answer

No AMS unit's automatic feed takes TPU rated 95A or softer. Carbon fiber nylon depends on the exact product. Wood PLA is listed for the full-size units; for the AMS lite, Bambu's pages disagree.

  • TPU 95A, 90A, 85A: Bambu lists the AMS, AMS 2 Pro and AMS lite as not compatible. An AMS HT can hold the spool as a sealed box, but you push the TPU by hand through a separate outlet on its back. The exception is Bambu's TPU for AMS, rated Shore 68D, which is listed for every AMS unit.
  • Carbon fiber nylon: Bambu PAHT-CF's store page lists the AMS, AMS 2 Pro and AMS HT, not the AMS lite. Bambu's PA6-CF page lists no AMS unit as compatible. Bambu's AMS notes say to avoid other brands' fiber-reinforced filament. A nylon spool fed from outside the AMS still needs a sealed box with desiccant.
  • Wood PLA: Bambu PLA Wood's store page lists every AMS unit as compatible. Bambu's filament guide lists wood PLA for the AMS, warns that some brands are brittle enough to break in the feed channel, and gives two different answers for the AMS lite.

Which unit you have changes the answer

Bambu's connection guide describes the AMS, AMS 2 Pro and AMS HT as sharing a two-stage feed: a feeder pushes filament to an assist motor, which drives it on to the toolhead. The AMS lite has one stage, and once printing starts only the extruder pulls the filament. Bambu's filament guide says the AMS has an extra transmission gear that adds feeding force, enough for some softer or rougher filaments, and that the AMS lite lacks it. Bambu's wiki also files its Notes on the AMS under the AMS 2 Pro and the AMS HT.

The AMS lite works only with A series printers, but not every A series printer uses one. With firmware 01.07.00.00 or later, an A1 series printer can run an AMS, AMS 2 Pro or AMS HT through the A Series AMS Hub, and an A2L can run AMS units and an AMS lite at once. Go by the unit the spool sits in.

Bambu's filament guide answers for the AMS and AMS lite only; the middle column follows Bambu's grouping of the AMS 2 Pro and AMS HT with the AMS. "Pages disagree" means Bambu's own pages give different answers; the section "Where Bambu's own pages disagree" sets them out.
FilamentAMS, AMS 2 Pro, AMS HTAMS lite
TPU 95A, 90A, 85ANot compatible; an AMS HT can hold the spool as a sealed box, fed by hand through its rear TPU outletNot compatible
Bambu TPU for AMS (68D)CompatibleCompatible
Other TPU rated 55D or harderNot compatible; only TPU for AMS is listed for the automatic feedPages disagree
TPEAvoidAvoid
Bambu PAHT-CFCompatiblePages disagree; its store page says not compatible
Bambu PA6-CFNot compatibleNot compatible
Other brands' PA-CF/GF, PAHT-CF/GF, PLA-CF/GFAvoidAvoid
PET-CF/GF (including Bambu PET-CF), PPA-CF/GF, PPS-CF/GFNot compatibleNot compatible
Bambu PLA-CFCompatibleCompatible
Bambu PETG-CFCompatiblePages disagree; its store page says not compatible
Other brands' PETG-CFPages disagreeAvoid
Bambu PLA WoodCompatiblePages disagree; its store page says compatible
Other brands' wood PLACompatible; some brands too brittlePages disagree
PLA GlowCompatible; wears the tubes fasterNot recommended; Bambu PLA Glow's page says not compatible
ABS, ABS-GFCompatibleNot recommended
PVA, BVOHOnly when dryOnly when dry

TPU: read the hardness number and its letter

Bambu's TPU guide ranks hardness from 77D, through 68D and 55D, down to 95A, 90A, 85A and softer. D is the harder scale, and a higher number means harder and less flexible. The AMS lite FAQ draws its line on that scale: 55D or harder can be used, 95A or softer cannot. The TPU guide lists one TPU for the automatic feed of every AMS unit: Bambu's TPU for AMS. The filament guide's table has a single TPU row, marked not compatible, with no separate entry for TPU for AMS.

So for the AMS, AMS 2 Pro and AMS HT, TPU for AMS is the one grade Bambu lists for a flexible part printed from an AMS slot. At 68D it is harder than every A-scale grade in that ranking, so if the part needs the give of 95A or 85A, that spool cannot use an AMS slot's automatic feed. Choosing filament by requirement covers that trade-off.

For softer TPU, Bambu's guides use a sealed dry box beside the printer or the AMS HT's rear TPU outlet, with the spool raised above the toolhead inlet. By printer:

  • A1 series: 85A is not supported. For 90A, remove one PTFE tube at the toolhead, feed the filament straight into the extruder inlet, and unload it by hand; the cutter cannot unload it.
  • P series: for 85A, remove the glass cover plate first, then load the filament into the extruder from above, not through a PTFE tube. 90A can run through a PTFE tube from the dry box. Both unload by hand, not with the cutter.
  • X1, H2, A2L and X2D: Bambu's TPU Printing Guide links a separate loading tutorial for each series. The same guide describes a TPU Feed Assist Module for H, X and P series printers, an upgrade that lets TPU feed through a dedicated inlet.
  • Any Bambu printer: TPU softer than 85A is not currently supported.
  • AMS HT: using the TPU outlet means no automatic feed or return, and no drying while printing that way.
  • Nozzle for 85A: Bambu's TPU Printing Guide and its P series TPU guide list 0.6 and 0.8 mm nozzles and the TPU high-flow hotend as compatible, and 0.4 mm as not compatible. The nozzle table in the general filament guide lists 0.4 mm as compatible. A 0.6 or 0.8 mm nozzle is the size all three pages accept. See nozzle sizes.

Carbon fiber nylon: check the product, not the brand

A Bambu label is not enough. The PAHT-CF store page lists the AMS, AMS 2 Pro and AMS HT as compatible and the AMS lite as not, and says it needs an enclosed printer. The PA6-CF page lists every AMS unit as not compatible. The filament guide still names Bambu PA-CF as compatible, but PA-CF was discontinued; the PAHT-CF page calls PAHT-CF its upgraded version.

For other brands, Bambu's AMS notes say to avoid third-party fiber-reinforced filament, including PA-CF/GF, because it can wear the PTFE tubes and break in the feed path. The filament guide flags certain brands as too brittle or too rough but does not name them, so there is no list to check a spool against.

A nylon spool that stays out of the AMS still needs protection from moisture. Bambu's filament guide marks desiccant protection during printing as required for carbon and glass fiber nylon. Bambu calls PA6-CF highly moisture-absorbent and PAHT-CF highly sensitive to humidity. So these spools feed from a sealed box with desiccant, not an open spool holder. Drying temperatures by method covers drying them first.

On an open-frame printer such as an A1 or P1P there is a second problem: Bambu's filament guide lists carbon and glass fiber nylons as not recommended there, and the PAHT-CF page calls PAHT-CF unsuitable for open-frame printers. That limits the AMS lite too. The filament guide's table lists Bambu PAHT-CF as compatible under a combined AMS / AMS lite heading, while its store page says the AMS lite is not compatible. Either way, the AMS lite works only with A series printers, which the filament guide classes as open-frame. Whether your printer can run a filament covers enclosure and nozzle needs.

Wood PLA: listed for the full-size units, disputed for the AMS lite

For the AMS, AMS 2 Pro and AMS HT, Bambu PLA Wood is listed as compatible on its store page, and the filament guide's table lists PLA Metal / Wood / Marble as compatible. That covers other brands' wood PLA too, subject to the guide's warning that certain brands, which it does not name, are brittle enough to break in the feed channel.

For the AMS lite, Bambu's pages give different answers. The PLA Wood store page lists all AMS units as compatible. The filament guide's text lists PLA Wood as not recommended for the AMS lite, but the same guide's table lists it as compatible under one combined AMS / AMS lite heading. The AMS lite FAQ does not mention wood PLA, but it sends too-brittle filament to the external spool. So the external spool is the one route none of these pages argues against.

Dry it first either way. The PLA Wood page says wood powder makes it more sensitive to moisture, and Bambu's AMS 2 Pro guide says filament that has absorbed too much moisture turns brittle and snaps more easily in the feed path.

Where Bambu's own pages disagree

  • Wood PLA in the AMS lite: the filament guide's text says not recommended, and its table says compatible. The PLA Wood store page lists every AMS unit.
  • Bambu PETG-CF in the AMS lite: its store page says not compatible and the filament guide says not recommended. The AMS lite FAQ lists it as compatible.
  • Other brands' PETG-CF in the AMS, AMS 2 Pro or AMS HT: the filament guide lists PETG-CF as compatible without naming a brand. Bambu's AMS notes say to avoid third-party fiber-reinforced filament.
  • Bambu PAHT-CF in the AMS lite: the filament guide's table lists it as compatible under a combined AMS / AMS lite heading. Its store page says not compatible.
  • Other TPU rated 55D or harder in the AMS lite: the AMS lite FAQ says it can be used. The TPU guide lists only TPU for AMS.
  • TPU for AMS: the filament guide's table has one TPU row, marked not compatible, and no entry for TPU for AMS. The TPU guide and the TPU for AMS store page list it for every AMS unit.
  • TPU 85A on a 0.4 mm nozzle: the TPU Printing Guide and the P series TPU guide say not compatible. The filament guide's nozzle table says compatible.

In each case one route avoids the question. For a spool, that is feeding it from outside the AMS, from a sealed box where the filament needs one. For TPU 85A, it is a 0.6 or 0.8 mm nozzle.

Compatible is not the same as wear-free

Bambu's compatibility table covers loading and unloading only. Its filament guide warns that abrasive filament, naming carbon fiber and glow, can grind down the AMS's internal PTFE feed channels over time, even after loading cleanly. Bambu's own PLA Glow page lists the AMS, AMS 2 Pro and AMS HT as compatible but says it can wear them faster. The tubes are replaceable, and Bambu's maintenance pages give intervals by time, not by kilograms:

  • AMS (first generation): every two months; monthly, or whenever wear shows, with carbon fiber or glow filament. The printer reminds you to check them every two months.
  • AMS lite: every two months; monthly for round-the-clock printing; promptly if they look worn.
  • AMS 2 Pro: no fixed interval; replace on feeding errors, loading resistance, or after extended heavy use with abrasive or composite filament.
  • AMS HT: the Bambu pages cited on this page give no interval. Its wiki index lists a separate guide to replacing the PTFE tube inside it.

Replacement tubes are 2.5 mm inside and 4 mm outside diameter; Bambu advises against other sizes. Lengths depend on the unit and the printer. Bambu's PTFE wear guide gives the first-generation AMS lengths: two 195 mm and two 230 mm tubes inside, plus 550 mm and 370 mm tubes at the output. The AMS lite FAQ lists two 730 mm and two 850 mm tubes for the A1, and two 580 mm and two 700 mm for the A1 mini. The AMS 2 Pro and AMS HT each have their own tube replacement guide on Bambu's wiki.

What to check on your own setup

  • Which unit the spool sits in: an AMS lite, or an AMS, AMS 2 Pro or AMS HT.
  • For Bambu filament, the Cautions for Use list on its store page. The pages for TPU for AMS, PAHT-CF, PA6-CF, PET-CF, PETG-CF, PLA-CF, PLA Glow and PLA Wood each state AMS compatibility there, and several name the AMS lite separately.
  • For TPU, the hardness number and its letter, A or D.
  • For another brand's spool, whether it is fiber-reinforced. Bambu's AMS notes say to avoid third-party fiber-reinforced filament in the AMS.
  • Whether the spool is dry. Bambu lists damp PVA and BVOH as too soft to feed, and describes both its carbon fiber nylons as moisture-sensitive.
  • For nylon, whether your printer is enclosed and whether the spool can sit in a sealed box with desiccant while it prints.
  • When the PTFE tubes were last changed, if abrasive filament has run through them.
  • Whether the spool fits the unit at all: spool sizes for each AMS unit.

What this page does not tell you

  • Bambu's filament guide gives answers for the AMS and AMS lite only. The AMS 2 Pro and AMS HT entries here follow Bambu's grouping of the three full-size units and the store pages that name all three.
  • Where Bambu's own pages give different answers, this page shows each one rather than choosing between them. Feeding the spool from outside the AMS is the route none of them argues against.
  • Bambu does not name the brands it calls too brittle or too rough, so this page cannot say whether a particular brand is one of them.
  • Bambu's PTFE tube intervals are by time, not by how much abrasive filament has run through. The Bambu pages cited here give no wear rate per kilogram and no interval for the AMS HT; check the AMS HT's own PTFE tube guide on Bambu's wiki.
  • Bambu revises its wiki and store pages. The answers here reflect those pages as of September 2026, so for a Bambu spool, check the Cautions for Use list on its store page before loading it.

Check it on your own equipment

These go to the makers and standards bodies this page draws on, so you can look up your exact model.

  • Official support pageBambu Lab filament guide: AMS & AMS lite section

    Section 3, 'AMS & AMS lite': Bambu's three failure types (too soft, too brittle, too hard and rough), the filaments listed for the AMS but not the AMS lite, a warning about long-term PTFE wear, and a table by filament type. The table splits the AMS and AMS lite only on some rows, and it lists PLA Metal / Wood / Marble as compatible for both, although the text above it lists PLA Wood as not recommended for the AMS lite.

    wiki.bambulab.com
  • Official support pageBambu Lab TPU Printing Guide

    Which AMS unit can hold standard TPU (only the AMS HT, as a sealed box with a rear outlet you feed by hand), that TPU for AMS feeds from every AMS unit, Bambu's Shore hardness order, which TPU grades each printer series supports, a nozzle table for each grade, the TPU Feed Assist Module for H, X and P series printers, and a loading tutorial for each printer series.

    wiki.bambulab.com
  • Official support pageBambu Lab AMS lite FAQ

    The AMS lite's TPU hardness line (55D or harder), its position on carbon and glass fiber filaments with Bambu PLA-CF and PETG-CF named as compatible, the filaments it sends to the external spool, and PTFE tube lengths for the A1 and A1 mini.

    wiki.bambulab.com
  • Official support pagePTFE Tube Wear in AMS and Maintenance Recommendations (first-generation AMS)

    For the first-generation AMS: replacement intervals (every two months, monthly with carbon fiber or glow filament), the 2.5 mm by 4 mm tube size, this unit's tube lengths, and step-by-step replacement for the feeder, hub and output tubes. The AMS 2 Pro and AMS HT have their own replacement guides.

    wiki.bambulab.com

More questions

Sources

Every figure on this page comes from one of these 24 documents. Makers revise their specifications, so each is dated: open it before you buy.

  1. TPU Printing Guide wiki.bambulab.com, Sep 23, 2026
  2. Filament guide - Printer, Nozzle, AMS, Build Plate, Glue Compatibility and Required Parameters wiki.bambulab.com, Sep 23, 2026
  3. CF Reinforced PET Filament | Bambu Lab US Store us.store.bambulab.com, Sep 23, 2026
  4. PLA-CF | Bambu Lab US Store us.store.bambulab.com, Sep 23, 2026
  5. PLA Glow | Bambu Lab US Store us.store.bambulab.com, Sep 23, 2026
  6. Notes for AMS wiki.bambulab.com, Sep 23, 2026
  7. AMS 2 Pro | Bambu Lab Wiki wiki.bambulab.com, Sep 23, 2026
  8. AMS HT | Bambu Lab Wiki wiki.bambulab.com, Sep 23, 2026
  9. Connection Guide for Multiple AMS Units with Different Printer Models wiki.bambulab.com, Sep 23, 2026
  10. Introduction to the modules and functions of AMS lite wiki.bambulab.com, Sep 23, 2026
  11. TPU for AMS | Bambu Lab US Store us.store.bambulab.com, Sep 23, 2026
  12. AMS lite FAQ wiki.bambulab.com, Sep 23, 2026
  13. PETG-CF | Bambu Lab US Store us.store.bambulab.com, Sep 23, 2026
  14. PLA Wood | Bambu Lab US Store us.store.bambulab.com, Sep 23, 2026
  15. TPU 90A printing guide for A1 series wiki.bambulab.com, Sep 23, 2026
  16. TPU 85A&90A printing guide for P series wiki.bambulab.com, Sep 23, 2026
  17. AMS 2 Pro and AMS HT - Frequently Asked Questions wiki.bambulab.com, Sep 23, 2026
  18. PAHT-CF | Bambu Lab US Store us.store.bambulab.com, Sep 23, 2026
  19. PA6-CF | Bambu Lab US Store us.store.bambulab.com, Sep 23, 2026
  20. Bambu Lab AMS 2 Pro Maintenance Recommendation wiki.bambulab.com, Sep 23, 2026
  21. PTFE Tube Wear in AMS and Maintenance Recommendations wiki.bambulab.com, Sep 23, 2026
  22. Bambu Lab AMS Maintenance Recommendation wiki.bambulab.com, Sep 23, 2026
  23. Bambu Lab AMS lite Maintenance Recommendation wiki.bambulab.com, Sep 23, 2026
  24. PTFE Tubes | Bambu Lab US Store us.store.bambulab.com, Sep 23, 2026